How To Connect Wifi Extender To Router With WPS – Updated May 2022

In this post, we’ll show you How To Connect Wifi Extender To Router With WPS on your computer. The QIG of each product is comparable, yet there is definitely something unusual about it as well.

This post will provide you with the answers to two questions:

  1. It is possible that you will have difficulty connecting your RE product to your Router/AP via the WPS button. Why?
  2. The WPS button on your dual-band RE product may only connect your RE product to the Wi-Fi 2.4G or 5G of your dual band router/AP, and not both bands’ Wi-Fi at the same time in some cases. Why?

Part A: First let’s explain how to configure the Ranger extender via the WPS button:

  1. Connect your Range Extender to a power outlet that is close to your primary Router/Access Point.
  2. The WPS button on your main router/AP should be pressed first, and then you should press the WPS button on the Range Extender shortly after.

Note 1: Please keep in mind that after you have pressed the WPS button on your Router/AP, you must press the WPS button on your Range Extender within 2 minutes of doing so. In order to avoid confusion, we strongly recommend that you press the WPS button on your RE product immediately after pressing the WPS button on your router.

Note 2: After pressing the WPS button on your Router/AP, the WPS LED on your Router/AP should begin to blink. If the WPS LED on your Router/AP does not blink, you will need to press the WPS button on your Router/AP several times until the WPS LED on your Router/AP blinks. The same rationale can be applied to RE products as well. When you press the WPS button on your Range Extender, the WPS/RE light on the Range Extender should begin to blink rapidly. If it doesn’t work, try again.

3. 2 minutes are allotted for the WPS process to complete. You can check the wireless signal LED on your Range Extender after 2 minutes if you want to be sure it is working properly. If it is illuminated (regardless of what colour it is or how many signal bars are there), it means that your Range Extender has been successfully linked to your main Router/AP.

4. If the wireless signal LED on your Range Extender is still off after 2 minutes, it signifies that the WPS process has not been completed. It is possible that you will need to repeat the WPS operation one or several more times, as well as the steps outlined above.

5. Finally, you may set your Range Extender in an appropriate location where you want to extend the coverage of your wireless network and enjoy the benefits of an expanded wireless network. There is no need to repeat the procedure. Once it’s finished, it will reconnect automatically every time you plug it back in after that.

You may also like: Best Speakers For Audio Technica Lp 120

Part B: Consider the following problem: “Sometimes you can only connect your dual-band RE product to the 2.4G or 5G Wi-Fi of your dual band router/AP via the WPS button, but not both bands’ Wi-Fi.” 

In reality, this problem is primarily caused by the dual band Router/AP, not by our dual-band Range Extender, which is described below:
Some dual band Router/APs only allow clients, including Range Extenders, to connect to a single frequency band (2.4G or 5G, depending on the Router/AP), with a single push of the WPS button on the router/control AP’s panel.

FAQs How To Connect Wifi Extender To Router With WPS

Does WiFi extender need WPS?

The WPS button on your extender is only used to connect to the router and can’t be used to connect devices. If you don’t have a WPS button on your hub/router, you can set up your extender using the web-based set-up with an internet browser.

You may also like: How to control Picolo subscription on your iPhone

Visual Guide

Default image
Wilson M. Stewart
I am a technology writer with an education in journalism. I have spent the past seven years writing about all sorts of tech topics, from games to gadgets to software and more.
Articles: 54

Leave a Reply

Physical Address

304 North Cardinal St.
Dorchester Center, MA 02124